# flash bios MegaCli -adpfwflash -f /scripts/firmware/lsi_imr_fw.rom -aALL MegaCli -adpfwflash -f imr_fw.rom -NoVerChk -aAll MegaCli -adpfacdefset -aALL # reset to factory default # controller info MegaCli -AdpAllinfo -aALL MegaCli -PDGetNum -a0 # nubmer of discs MegaCli -PDInfo -PhysDrv [64:0] -aALL MegaCli -PDMakeJBOD -PhysDrv[64:4] # clear controller config to defaults MegaCli -CfgClr -aALL # delete all MegaCli -CfgLdDel -LALL -aALL # create raid MegaCli -CfgLdAdd -r5 [64:0, 64:1, 64:2, 64:3] -a0 MegaCli -CfgLdAdd -r0 [64:4,64:5,64:6,64:7] -a0 # get free devices MegaCli -PDList -a0 | grep -e '^Enclosure Device ID:' -e '^Slot Number:' # get raid info MegaCli -LDInfo -Lall -aALL MegaCli -PDMakeGood -PhysDrv[64:4] -force -aALL > /dev/null MegaCli -PDMakeGood -PhysDrv[64:5] -force -aALL > /dev/null MegaCli -PDMakeGood -PhysDrv[64:6] -force -aALL > /dev/null MegaCli -PDMakeGood -PhysDrv[64:7] -force -aALL > /dev/null MegaCli -PDMakeJBOD -PhysDrv[64:4,64:5,64:6,64:7] -a0 MegaCli -CfgLdAdd -r0 [64:4,64:5,64:6,64:7] -a0 MegaCli -AdpEventLog -GetEvents -f logfile -aALL # Dump all events from the adapters event log to a file named logfile MegaCli -PDList -aAll # Dump information about all Phsyical Disks MegaCli -LDInfo -LAll -aAll # Dump information about all Logical Disks on all adapters MegaCli -LdPdInfo -aAll # Dump information of all logical and physical disks on all known adapters MegaCli -AdpSetProp -EnableJBOD 1 -aALL MegaCli -CfgDsply -aAll # adapter diagnostic MegaCli -AdpDiag -a0 Controller information MegaCli -AdpAllInfo -aALL MegaCli -CfgDsply -aALL MegaCli -AdpEventLog -GetEvents -f events.log -aALL && cat events.log Enclosure information MegaCli -EncInfo -aALL Virtual drive information MegaCli -LDInfo -Lall -aALL Physical drive information MegaCli -PDList -aALL MegaCli -PDInfo -PhysDrv [E:S] -aALL Battery backup information MegaCli -AdpBbuCmd -aALL Controller management Silence active alarm MegaCli -AdpSetProp AlarmSilence -aALL Disable alarm MegaCli -AdpSetProp AlarmDsbl -aALL Enable alarm MegaCli -AdpSetProp AlarmEnbl -aALL Physical drive management Set state to offline MegaCli -PDOffline -PhysDrv [E:S] -aN Set state to online MegaCli -PDOnline -PhysDrv [E:S] -aN Mark as missing MegaCli -PDMarkMissing -PhysDrv [E:S] -aN Prepare for removal MegaCli -PdPrpRmv -PhysDrv [E:S] -aN Replace missing drive MegaCli -PdReplaceMissing -PhysDrv [E:S] -ArrayN -rowN -aN Rebuild drive MegaCli -PDRbld -Start -PhysDrv [E:S] -aN MegaCli -PDRbld -Stop -PhysDrv [E:S] -aN MegaCli -PDRbld -ShowProg -PhysDrv [E:S] -aN Clear drive MegaCli -PDClear -Start -PhysDrv [E:S] -aN MegaCli -PDClear -Stop -PhysDrv [E:S] -aN MegaCli -PDClear -ShowProg -PhysDrv [E:S] -aN MegaCli -PDMakeGood -PhysDrv[E:S] -aN This changes drive in state Unconfigured-Bad to Unconfigured-Good. Set the drive offline, if it is not already offline due to an error MegaCli -PDOffline -PhysDrv [E:S] -aN Mark the drive as missing MegaCli -PDMarkMissing -PhysDrv [E:S] -aN Prepare drive for removal MegaCli -PDPrpRmv -PhysDrv [E:S] -aN If you’re using hot spares then the replaced drive should become your new hot spare drive: MegaCli -PDHSP -Set -PhysDrv [E:S] -aN In case you’re not working with hot spares, you must re-add the new drive to your RAID virtual drive and start the rebuilding MegaCli -PdReplaceMissing -PhysDrv [E:S] -ArrayN -rowN -aN MegaCli -PDRbld -Start -PhysDrv [E:S] -aN MegaCli -CfgLdAdd -r0 [0:1, 0:1] -a0 MegaCli -LDInfo -Lall -aALL # View all controleler informations MegaCli -AdpAllInfo -aAll MegaCli -LDSetProp CachedBadBBU -LALL -aALL Delete all devices MegaCli -CfgLdDel -LALL -aALL MegaCli -CfgLdAdd -r1 [252:0,252:1] -a0 MegaCli -CfgLdAdd -r10 [252:0,252:1,252:2,252:3] -a0 # create RAID5 MegaCli -CfgLdAdd -r5 [64:0,64:1,64:2,64:3] -a0 # create RAID10 MegaCli -CfgSpanAdd -r10 -Array0[64:0,64:1] -Array1[64:2,64:3] -a0 # create RAID10 MegaCli -AdpSetProp -EnableJBOD 1 # Enable disks cache MegaCli -LDSetProp EnDskCache -LAll -aAll # Force flash MegaCli -adpfwflash -f ./12.12.0-0111.rom -NoVerChk -a0 # load controller defauts MegaCli -adpfacdefset -aALL